921A钢在海水中腐蚀的力学化学效应

为了研究弹性应力和弹塑性应变对921A船体钢在模拟海水中腐蚀行为的影响,采用自制的载荷-电化学实验装置对921A钢在载荷与腐蚀介质协同作用时的开路电位、动电位极化曲线和电化学阻抗谱等电化学性能进行了测试,并由电化学阻抗谱拟合得到的电荷传递电阻定义载荷下的腐蚀速率修正因子,将实验得到的腐蚀速率修正因子与理论值进行了对比。结果表明:弹性拉应力与弹性压应力对力学化学效应的影响具有对称性。力学化学效应随着弹性应力的增大而增大,随着弹塑性应变的增大先增大后减小。弹塑性应变对力学化学效应的影响远远大于弹性应力的影响。在研究范围内,弹塑性应变引起的腐蚀电位负移量最大为62.6 mV,相应的腐蚀速率修正因子高达4.113,而弹性应力引起的腐蚀电位负移量最大为24.5 mV,相应的腐蚀速率修正因子为1.746。由此可见,应力应变对921A钢在海水中腐蚀行为的影响不容忽视。     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

几种防锈液对T52钢在酸性介质中耐蚀性的影响

研究了几种防锈液对T52(10Ti热)钢在Ph=5.0酸性水溶液中耐蚀性能的影响.用线性极化和交流阻抗法对这些防锈液的耐蚀性能进行了综合评估,试验结果表明:亚硝酸钠类、含氨基和羧基的有机化合物类两种防锈液的耐蚀性能较好;并用动电位扫描法对上述防锈液的作用机理进行了初步探讨,试验表明:上述防锈液主要是抑制电极的阳极过程.     

“9·11”世贸大楼坍塌原因数值分析

数值分析表明,"9·11"恐怖袭击事件造成纽约世贸大楼的内部竖向承重钢结构的防火保护层在爆炸中严重脱落,火灾高温使钢材强度大幅度降低,导致着火层群柱失稳,上部巨大的冲击荷载把下层柱逐层压渍,引发连续坍塌.最后对超高层建筑的结构设计提出建议.     

钢筋钢纤维混凝土既有裂缝梁中钢纤维阻裂作用有限元分析

通过建立钢筋钢纤维混凝土既有裂缝梁和钢筋混凝土既有裂缝梁的有限元分析模型,借助ANSYS分析了两种梁在荷载作用下的裂缝尖端处应力、裂缝宽度增幅和挠度并作出对比。分析结果表明钢纤维对裂缝开展有很好的阻止作用,而且能明显缓和裂缝尖端处应力,减小梁的挠度。     

钢筋混凝土外粘钢板结构裂缝的有限元数值模拟

随着高技术武器的不断发展,防护工程正面临着前所未有的威胁和挑战,新型防护结构及材料已经成为研究的热点。针对这一实际背景,运用ANSYS大型有限元软件,采用数值模拟的方法对普通钢筋混凝土结构和外粘钢板混凝土结构在相同均布面荷载作用下的变形、钢筋应力以及结构裂缝的开展情况进行了比较。结果表明外粘钢板的钢筋混凝土结构能够大大增强结构的抗力,并且有效的抑制了裂缝的开展。     

扭转约束对无防火保护钢柱抗火性能影响分析

应用ANSYS软件计算了钢柱在标准升温模式下的温度场,然后利用ANSYS的耦合分析模块,将温度场导入结构分析,分析了不同约束下轴心受压钢柱在温度升高时的力学反应,同时考虑了荷载比以及长细比对不同约束钢柱抗火性能的影响.研究表明:扭转约束钢柱的抗火性能要优于柱端没有扭转约束的简支柱;当钢柱长细比系数在30以内时,扭转约束...     

Experimental investigation on anti-penetration performance of polyurea-coated ASTM1045 steel plate subjected to projectile impact

In this study, the anti-penetration performance of polyurea/ASTM1405-steel composite plate subjected to high velocity projectile was analyzed. Two kinds of modified polyurea material (AMMT-053 and AMMT-055) were selected and a ballistic impact testing system including speed measuring target system and high-speed camera was designed. This experiment was conducted with a rifle and 5.8 mm projectile to explore the effects by the polyurea coating thickness, the polyurea coating position and the glass-fiber cloth on the anti-penetration performance of polyurea/ASTM1405-steel composite plate. The result showed that the effects of polyurea coating position were different between two types of polyurea, and that the effects of glass-fiber position were disparate between two types of polyurea as well. For AMMT-053 polyurea material, it was better to be on front face than on rear face; whereas for AMMT-055 pol-yurea, it was better to be on rear surface although the difference was very subtle. Additionally, formulas had been given to describe the relationship between the effectiveness of polyurea and the thickness of polyurea coating. In general, AMMT-055 had better anti-penetration performance than AMMT-053. Furthermore, five typical damage modes including self-healing, crack, local bulge, spallation and local fragmentation were defined and the failure mechanism was analyzed with the results of SHPB test. Additionally, the bonding strength played an important role in the anti-penetration performance of polyurea/steel composite plate.     

试验面选取对碳钢点蚀电位测量的影响

采用金相分析技术和准稳态极化试验研究了试样试验面选取对碳钢点蚀电位测量的影响.结果表明,当不同试验面的夹杂物形态有很大差异时,测得的点蚀电位有较明显的差异.     

轻集料钢筋混凝土梁受弯性能试验研究

轻集料混凝土应用于港口工程是一个待研究的课题.通过对4根轻集料钢筋混凝土梁和2根普通混凝土梁进行的抗弯对比试验,研究了轻集料钢筋混凝土粱的抗弯力学性能.结果表明,轻集料钢筋混凝土梁在承受正常荷载时,其力学性能与普通混凝土梁相比无明显差异;在破坏时脆性较同等级普通混凝土粱略大,延性略差.但考虑到轻集料混凝土的优点,在实际工程中可代替普通混凝土受弯构件工作.